Thermal Interface Materials - THERMAL PASTE - Thermal Compounds
| Thermal Adhesive Epoxies |
| CPU & Heatsink Cleaners |
Acoustic PC only offers the best when it comes to computer thermal conducting compound, THERMAL PASTE, thermal grease, PC thermal epoxy
and thermal adhesive, such as Silver adhesive epoxy, and Alumina Adhesive epoxy By Arctic Silver thermal tape, and thermal material remover
ArctiClean and purifying products. Acoustic PC highly recommends the entire Artic Silver product line including non-conductive Ceramique for your pc
thermal needs. However we do provide other excellent new solution such as OCZ Technology Freeze, IC Diamond 7 Carat, By Inovation cooling,
Noctua Tim Solution non electrically conductive Yet works with-in a degree of most thermaly conductive high-performance thermal compounds,
Zalman Super Thermal grease, Thermalright Chill Factor and shin-etsu thermal paste.
Check out this Informative Article : How To Apply Thermal Compound >> Apply Thermal Paste.
and thermal adhesive, such as Silver adhesive epoxy, and Alumina Adhesive epoxy By Arctic Silver thermal tape, and thermal material remover
ArctiClean and purifying products. Acoustic PC highly recommends the entire Artic Silver product line including non-conductive Ceramique for your pc
thermal needs. However we do provide other excellent new solution such as OCZ Technology Freeze, IC Diamond 7 Carat, By Inovation cooling,
Noctua Tim Solution non electrically conductive Yet works with-in a degree of most thermaly conductive high-performance thermal compounds,
Zalman Super Thermal grease, Thermalright Chill Factor and shin-etsu thermal paste.
Check out this Informative Article : How To Apply Thermal Compound >> Apply Thermal Paste.
| Thermal Compounds |
Acoustic PC : How To apply themal paste...
An Informative Article : How To Apply Thermal Compound >> Apply Thermal Paste.
Introduction
techniques involving large capacity heat sinks, good air flow and careful management of thermal interface resistances. A well designed thermal the
correct heat sink has been selected, it must be carefully joined to the semiconductor package to ensure efficient heat transfer through is newly
formed thermal interface.
Attaching a heat sink to a semiconductor package requires that two solid surfaces be brought together into intimate contact. Unfortunately, no matter
how well-prepared, solid surfaces are never really flat or smooth enough to permit intimate contact. All surfaces have a certain roughness due to
microscopic hills and valleys as shown in Figure 1A. Superimposed on this surface roughness is a macroscopic non-planarity in the form of a
concave, convex or twisted shape as shown in Figure 1B. As two such surfaces are brought together, only the hills of the surfaces come into physical
contact. The valleys are separated and form air-filled gaps.
Arctic Silver, Inc. is the premier manufacturer of high-performance thermally conductive compounds and adhesives for modern computers and
other high-power electronics.
Arctic Silver No. 5 AKA AS5
A unique high-density filling of micronized silver and enhanced thermally conductive ceramic particles provides superior level of performance and
stability. Arctic Silver 5 is optimized for use between modern high-power CPUs and high performance heatsinks or water-cooling solutions.
Ceramique
A high-density layered composite of five unique shapes of thermally conductive aluminum oxide, boron nitride and zinc oxide sub-micron particles
maximizes particle-to-particle contact area and thermal transfer.
ArctiClean
Our new TIM remover and thermal surface purifier, ArctiClean, is the first retail product to emerge from the union of Arctic Silver and Nanotherm
technology. ArctiClean is available at Arctic Silver dealers worldwide. In addition to ArctiClean both companies co-developed Ambrosia HT, a
high-temperature thermal grease that was released for OEM and laboratory use last summer and has gained great acceptance for use in special
high-temperature applications.
Silver Adhesive
Arctic Silver Thermal Adhesive IS NOT intended to be used between a CPU and the CPU heatsink.
On a CPU, only use. Arctic Silver Thermal Compound
Silver Adhesive Features:
Made with 99.8% pure micronized silver.
62% to 65% silver content by weight.
Superior thermal conductivity. Greater than 7.5 W/mK
Temperature range:
- 40C to >150C (Bond strength is weakened at temperatures
below 0C due to crystallization.)
Negligible electrical conductivity:
Arctic Silver Thermal Adhesive was formulated to conduct heat, not electricity.
NOTE: Even though Arctic Silver Thermal Adhesive is specifically engineered for high electrical resistance, it should be keep away from electrical
traces, pins, and leads. The cured adhesive is slightly capacitive and could potentially cause
problems if it bridged two close-proximityelectrical paths.
Compliancy:
RoHS Compliant.
Arctic Silver Thermal Adhesive is sold in:
A set of Arctic Silver Thermal Adhesive consists of two tubes containing a total of 7 grams of adhesive
(3.5 grams of Part A and 3.5 grams of Part B) and a plastic reusable mixing wand.
CAUTION!
Arctic Silver Thermal Adhesive is a permanent adhesive. Components you attach with Arctic Silver Thermal Adhesive will stay attached forever.
Arctic Silver Thermal Adhesive should be kept cold and away from UV light (sunlight and florescent lighting). We recommend refrigerating the
unused material and allowing it to come to room temperature prior to use.
An Informative Article : How To Apply Thermal Compound >> Apply Thermal Paste.
Introduction
techniques involving large capacity heat sinks, good air flow and careful management of thermal interface resistances. A well designed thermal the
correct heat sink has been selected, it must be carefully joined to the semiconductor package to ensure efficient heat transfer through is newly
formed thermal interface.
Attaching a heat sink to a semiconductor package requires that two solid surfaces be brought together into intimate contact. Unfortunately, no matter
how well-prepared, solid surfaces are never really flat or smooth enough to permit intimate contact. All surfaces have a certain roughness due to
microscopic hills and valleys as shown in Figure 1A. Superimposed on this surface roughness is a macroscopic non-planarity in the form of a
concave, convex or twisted shape as shown in Figure 1B. As two such surfaces are brought together, only the hills of the surfaces come into physical
contact. The valleys are separated and form air-filled gaps.
Arctic Silver, Inc. is the premier manufacturer of high-performance thermally conductive compounds and adhesives for modern computers and
other high-power electronics.
Arctic Silver No. 5 AKA AS5
A unique high-density filling of micronized silver and enhanced thermally conductive ceramic particles provides superior level of performance and
stability. Arctic Silver 5 is optimized for use between modern high-power CPUs and high performance heatsinks or water-cooling solutions.
Ceramique
A high-density layered composite of five unique shapes of thermally conductive aluminum oxide, boron nitride and zinc oxide sub-micron particles
maximizes particle-to-particle contact area and thermal transfer.
ArctiClean
Our new TIM remover and thermal surface purifier, ArctiClean, is the first retail product to emerge from the union of Arctic Silver and Nanotherm
technology. ArctiClean is available at Arctic Silver dealers worldwide. In addition to ArctiClean both companies co-developed Ambrosia HT, a
high-temperature thermal grease that was released for OEM and laboratory use last summer and has gained great acceptance for use in special
high-temperature applications.
Silver Adhesive
Arctic Silver Thermal Adhesive IS NOT intended to be used between a CPU and the CPU heatsink.
On a CPU, only use. Arctic Silver Thermal Compound
Silver Adhesive Features:
Made with 99.8% pure micronized silver.
62% to 65% silver content by weight.
Superior thermal conductivity. Greater than 7.5 W/mK
Temperature range:
- 40C to >150C (Bond strength is weakened at temperatures
below 0C due to crystallization.)
Negligible electrical conductivity:
Arctic Silver Thermal Adhesive was formulated to conduct heat, not electricity.
NOTE: Even though Arctic Silver Thermal Adhesive is specifically engineered for high electrical resistance, it should be keep away from electrical
traces, pins, and leads. The cured adhesive is slightly capacitive and could potentially cause
problems if it bridged two close-proximityelectrical paths.
Compliancy:
RoHS Compliant.
Arctic Silver Thermal Adhesive is sold in:
A set of Arctic Silver Thermal Adhesive consists of two tubes containing a total of 7 grams of adhesive
(3.5 grams of Part A and 3.5 grams of Part B) and a plastic reusable mixing wand.
CAUTION!
Arctic Silver Thermal Adhesive is a permanent adhesive. Components you attach with Arctic Silver Thermal Adhesive will stay attached forever.
Arctic Silver Thermal Adhesive should be kept cold and away from UV light (sunlight and florescent lighting). We recommend refrigerating the
unused material and allowing it to come to room temperature prior to use.
 |
 |
|||
 |
 |
|||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
 |
 |
||
 |
||||
 |
||||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
 |
 |
||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
 |
 |
||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
||||
 |
|||||||||
 |
 |
 |
 |
 |
 |
 |
|||
 |
 |
 |
 |
||||||